Performance of surface ionic conduction single chamber fuel cell prepared by the sol gel method

The performance of surface ionic conduction single chamber fuel cell (SIC‐SCFC) prepared by the sol gel method was studied on electric characteristics due to the differences of the operating temperature and humidity, the electrode distance and electrolyte film depth, and multiple cells with the series and parallel connections. The SIC–SCFC was arranged the both anode of Pt and cathode of Au on the boehmite electrolyte. The open circuit voltage (OCV) of single cell achieved a maximum of 530mV in the dry gas mixtures of O₂/H₂=50% in room temperature operation, and but it became decrease as over 60%. The OCV was maintained the constant value between operating temperatures of 30°C to 80°C, and but it was decreased sharply at over 90°C because a humidity on the cell became lower as increasing operating temperature. Then, the cell property was improved to 120°C by adding to the humidity of 70% using a humidifier. The electrode distance and the electrolyte film depth of SIC‐SCFC found to be contributed to the reductions of the cell resistance and the surface roughness on the electrode, respectively. Moreover, the power property of SIC‐SCFC was significantly improved by cell stacks comprised of the series or parallel connection of a cell.     

一种5 重real-time PCR筛查转基因水稻方法的建立

以转基因水稻中最常用的CaMV35S启动子、NOS终止子、Cry1Ab/Ac基因、HPT基因及SPS水稻内标基因为研究对象，利用5 种不同的荧光信号（FAM、HEX、Taxas Red、Cy5、Cy5.5）进行多重实时聚合酶链式反应（real-time polymerase chain reaction，real-time PCR）检测方法的研究。通过引物组合筛选、反应体系优化、特异性测试、灵敏度测试、适用性测试等一系列实验，建立了5 重real-time PCR方法，灵敏度可达0.032%。此方法具有灵敏度高、结果准确、通量大等优点，可实现水稻中转基因成分的快速、高效检测。     

Three‐dimensional color prediction modeling of single‐ and double‐layered woven fabrics

In this research, the three‐dimensional structural and colorimetric modeling of three‐dimensional woven fabrics was conducted for accurate color predictions. One‐hundred forty single‐ and double‐layered woven samples in a wide range of colors were produced. With the consideration of their three‐dimensional structural parameters, three‐dimensional color prediction models, K/S‐, R‐, and L*a*b*‐based models, were developed through the optimization of previous two‐dimensional models which have been reported to be the three most accurate models for single‐layered woven structures. The accuracy of the new three‐dimensional models was evaluated by calculating the color differences ΔL*, ΔC*, Δh°, and ΔE_CMC(2:1) between the measured and the predicted colors of the samples, and then the error values were compared to those of the two‐dimensional models. As a result, there has been an overall improvement in color predictions of all models with a decrease in ΔE_CMC(2:1) from 10.30 to 5.25 units on average after the three‐dimensional modeling.     

增效过磷酸钙的增效机制及其对玉米生长的影响

利用猪毛、风化煤和腐植酸钠的水解液为增效剂制备了一种增效过磷酸钙,探讨了增效过磷酸钙的增效机制及其对玉米生长的影响。结果表明,蒸馏水浸提条件下,增效过磷酸钙能减缓水溶磷的释放,具备较高的pH值缓冲性。与普通过磷酸钙相比,增效过磷酸钙处理的玉米生物量平均增加了41.9%,吸磷量和吸钙量分别增加了61.7%和27.8%,根系活力增加了24.3%。该研究结果对过磷酸钙生产的技术改进具有指导意义。     

The effect of baking time,fillet radius,and hardness on the lifecycles of pole fastening screws in an electric motor with hydrogen embrittlement

In order to protect bolts from corrosion, electroplating such as zinc plating is widely used. However, hydrogen can easily penetrate or diffuse into the vacancies and dislocations between the lattices of bolt steel during electroplating. As the diffused hydrogen defects inside the lattice are in gaseous form, small cracks can easily be produced due to high pressure from the hydrogen gas. In this research, in order to determine the root cause of the fracture in pole fastening screws resulting from hydrogen embrittlement in typical electric motors, additional factors that accelerate hydrogen embrittlement fracture were selectively applied, including a small fillet in the head–shank transition and excessive hardness, and parametric study was performed experimentally.     

磁絮凝强化技术处理厌氧消化污泥脱水液

为满足后续生物处理单元对固体悬浮物（SS）和铁浓度的进水要求，采用磁絮凝强化技术对厌氧消化污泥脱水液进行预处理。通过正交试验和单因素试验，本文考察了混凝水力条件、聚合氯化铝（PAC）投加量、聚丙烯酰胺（PAM）投加量、磁粉投加量及药剂投加顺序对磁絮凝效果的影响。试验结果表明：磁絮凝强化技术在快搅300r/min（2min）、慢搅100r/min（15min）、静置10min时，依次投加磁粉（40mg/L）、PAC（30mg/L）、PAM（4mg/L）时处理效果最好。在此运行条件下，SS和Fe³⁺去除率分别为97.61%、98.24%、絮凝指数（FI值）取得最大值、zeta电位绝对值最小，絮凝效果最佳。与对照相比，磁絮凝强化技术对SS和Fe³⁺去除率分别可提高3.70%和10.82%，同时絮体最大沉降速度可提高33%。磁絮凝技术处理后的出水不仅可以满足后续生物处理单元对SS和铁浓度的要求，还可以有效提高磁絮凝体的沉降速度，减小沉淀时间，具有较好的实用价值。     

单相硼化物的制备及摩擦磨损性能研究

为了深入研究渗硼层中硼化物的性能，采用真空感应熔炼法制备单相硼化物材料。观察分析制备的硼化物微观组织，测试其力学性能。采用MMU-5G型销-盘式摩擦磨损试验机，在干摩擦条件下，研究了不同载荷下单相硼化物的摩擦学性能，观察其磨损表面形貌特征，探讨其磨损方式。结果表明：制备的硼化物为单一相，试样纯度高，试样的平均显微硬度为HV2065，平均断裂韧性值为1.68 MPa·m1/2；硼化物的断口处没有宏观的塑性变形，断口齐平光亮，表现为脆性断裂特征；干摩擦条件下随着载荷从10 N增加到30 N，硼化物的摩擦因数先降低后增加，20 N载荷时达到最小值，而其磨损量随着载荷的增加不断上升；随着载荷从10 N增加到30 N，磨损表面的粗糙度先逐渐上升后急剧上升； 10~20 N载荷下，硼化物的磨损以磨粒磨损为主，而25~30 N载荷下，硼化物的主要磨损方式从磨粒磨损转变为脆性破损。     

小断块单元油藏单井多周期CO2吞吐强化采油研究

低渗小断块油藏控制单元井间连通性差、边界封闭、地层能量有限、开采中地层能量下降很快，难以采用早期注水等方式大规模开采。用CO2吞吐强化采油对此类油藏可能是一种有效的方法，为此进行了相关研究：首先对油井目前流体进行相态研究，然后对油藏流体进行CO2膨胀实验，再将注气前、后的地层流体的物性进行对比，确定CO2增产机理；在此基础上建立单井CO2吞吐的数值模拟模型并对注气前生产历史进行拟合，用拟合好的模型对CO2吞吐强化采油过程中周期注入量、注气速度、焖井时间和生产速度等因素进行敏感性分析，从而得出适合于小断块单元油藏单井CO2吞吐强化采油的优选方案，并对第一周期生产指标进行了预测，在此基础上，对第二周期的周期注入量进行了分析，得出相关油井已不适合进行第二周期吞吐的结论，为油井CO2吞吐强化采油可行性的工艺方案设计提供了技术依据。